6.3 Chemical Weathering

Chemical weathering alters the chemical composition of the rock and results from chemical changes to minerals that become unstable when they are exposed to surface conditions. The kinds of changes that take place are highly specific to the mineral and the environmental conditions. Some minerals, like quartz, are virtually unaffected by chemical weathering, while others, like feldspar, are easily altered. In general, the degree of chemical weathering is greatest in warm and wet climates and least in cold and dry climates. The important characteristics of surface conditions that lead to chemical weathering are the presence of water (in the air and on the ground surface), the abundance of oxygen, and the presence of carbon dioxide, which produces weak carbonic acid when combined with water. That process, which is fundamental to most chemical weathering, can be shown as follows:

Here we have water (e.g., as rain) plus carbon dioxide in the atmosphere, combining to create carbonic acid. Then carbonic acid dissociates (comes apart) to form hydrogen and bicarbonate ions. The amount of CO₂ in the air is enough to make weak carbonic acid.  There is typically much more CO₂ in the soil, so water that percolates through the soil can become more acidic.  In either case, this acidic water is critical to chemical weathering.

In some types of chemical weathering, the original mineral becomes altered to a different mineral. For example, feldspar is altered—by hydrolysis—to form clay minerals plus some ions in solution. In other cases, the minerals dissolve completely, and their components go into solution. For example, calcite (CaCO₃) is soluble in acidic solutions.

The hydrolysis of feldspar can be written like this:

This reaction shows calcium-bearing plagioclase feldspar, but similar reactions could also be written for sodium or potassium feldspars. In this case, we end up with the mineral kaolinite and calcium and carbonate ions in solution. Those ions can eventually combine (probably in the ocean) to form the mineral calcite. The hydrolysis of feldspar to clay is illustrated in Figure 6.12, which shows two images of the same granitic rock, a recently broken fresh surface on the left and a clay-altered weathered surface on the right. Other silicate minerals can also undergo hydrolysis, although the end results will be slightly different. For example, pyroxene can be converted to the clay minerals chlorite or smectite, and olivine can be converted to the clay mineral serpentine.

Oxidation is another very important chemical weathering process. The oxidation of the iron in a ferromagnesian silicate starts with the dissolution of the iron. For olivine, the process looks like this where olivine in the presence of carbonic acid is converted to dissolved iron, carbonate, and silicic acid:

But in the presence of oxygen and carbonic acid, the dissolved iron is then quickly converted to the mineral hematite:

The equation shown here is for olivine, but it could apply to almost any other ferromagnesian silicate, including pyroxene, amphibole, or biotite. In this way, iron in the sulphide minerals (e.g., pyrite) can also be oxidized. And the mineral hematite is not the only possible end result, as a wide range of iron oxide minerals can form in this way. The results of this process are illustrated in Figure 6.13, which shows a granitic rock in which some of the biotite and amphibole have been altered to form the iron oxide mineral limonite.

A special type of oxidation occurs in areas where the rocks have elevated levels of sulphide minerals, especially pyrite (FeS₂). Pyrite reacts with water and oxygen to form sulphuric acid, as follows:

The runoff from areas where this process occurs is known as acid rock drainage (ARD), and even rock with 1% or 2% pyrite can produce significant ARD. Some of the worst examples of ARD are at metal mine sites, especially where pyrite-bearing rock and waste material have been mined from deep underground, piled up, and left exposed to water and oxygen. One example of that is the Mt. Washington Mine near Courtenay on Vancouver Island (Figure 6.14), but there are many similar sites across Canada and around the world.

At many ARD sites, the pH of the runoff water is less than 4 (very acidic). Under these conditions, metals such as copper, zinc, and lead are quite soluble, which can lead to toxicity for aquatic and other organisms. For many years, the river downstream from the Mt. Washington Mine had so much dissolved copper in it that it was toxic to salmon. Remediation work has since been carried out at the mine, and the situation has improved.

The hydrolysis of feldspar and other silicate minerals and the oxidation of iron in ferromagnesian silicates all serve to create softer and weaker rocks than they were, to begin with, and thus more susceptible to mechanical weathering.

The weathering reactions that we’ve discussed so far involved transforming one mineral to another mineral (e.g., feldspar to clay) and releasing some ions in solution (e.g., Ca²⁺ or Fe²⁺). Some weathering processes involve the complete dissolution of a mineral. Calcite, for example, will dissolve in weak acid to produce calcium and bicarbonate ions. The equation is as follows:

Calcite is the major component of limestone (typically more than 95%), and under surface conditions, limestone can dissolve completely, as shown in Figure 6.15. Limestone also dissolves at relatively shallow depths underground, forming limestone caves.

Media Attributions

• Figure 6.12, 6.13, 6.14, 6.15: © Steven Earle. CC BY.